新加坡2分彩计划软件

John Broskie's Guide to Tube Circuit Analysis & Design

07 may 2019                                                                                post 464

A Corner Dipole Loudspeaker
新加坡2分彩计划软件 The famous Klipschorn solved two problems: how to make a bass horn and what to do with room corners. Placing the Klipschorn in the corner extended the folded bass horn's flaring into the room, allowing deeper bass reproduction; in addition, the Klipschorn makes use of what is otherwise often dead space. I have seen triangular PA loudspeakers that were designed for corner use, but no other HiFi speaker. Why not? One problem is booming bass and another is excessive wall reflections, something the Klipschorn didn't suffer from as the horizontal placement of its horn midrange and horn tweeter resulted wide vertical radiation, but limited horizontal radiation. Ordinary drivers would not be so lucky. Imagine mirrored walls and all the reflections of the loudspeaker that would appear.

新加坡2分彩计划软件well, what would happen if we placed a dipole speaker in the corner, not so close as to trap the rear sound radiation, but far enough away so that the rear sound at the dipole's sides would, when combined with the front radiation, cancel? the rear waves would cause some trouble, as they would bounce back towards the dipole, which would truly bother a planar loudspeaker, such as an electrostatic type; but as a dynamic driver would constitute so much less of the dipole surface area, we can worry a lot less. one workaround, nonetheless, would be to place a tall roll of sound-absorbing batting behind the dipole.

新加坡2分彩计划软件one problem with flat dipoles is that the panel tends to rock back and forth. the workaround is to place center panel perpendicular with the dipole panel.

the t shape stabilizes the panel and would prove useful for adhering acoustic foam to absorb the reflected sound waves. okay, what if we only the dipole panel for loading the lower-midrange and letting a subwoofer handle frequencies below 150hz?

such an arrangement would allow us to use a much narrower panel, say 18 inches wide.

four 5-inch mid-woofers cover the frequencies from 150hz to 4khz. the spacing should be set to destructive ratios, for example with spacings from the top to bottom drivers of 5in, 7in, 13in, and 17in. the tweeter is a horn-load ribbon design, rotated 90 degrees to limit horizontal dispersion and promote vertical dispersion. (usually, we desire a dipole speaker whose rear radiation matches the front radiation in frequency bandwidth, but not with this corner placement.)

the subwoofer would only reproduce frequencies below 150hz and could be much less efficient than the rest of the drivers, as it would be self powered. another possible corner dipole would be much larger and would hold two long side panels made of either sheet glass or plexiglas (i.e. clear acrylic sheet) that make the dipole look much smaller, while still providing more loading for low frequencies, so a 100hz crossover could be used between the two mid-bass drivers and the heavy woofer.

the heavy woofer gets its own sealed enclosure and acoustic foam adheres to the t plank of wood.

A horn-loaded high-frequency driver is shown, which would deliver high SPLs. The two mid-woofers would be professional-audio drivers and would each be placed in series with an 8-ohm power resistor. Why? We need to obtain an 8-ohm impedance for the entire loudspeaker and we wish to increase the drivers' Qes, which in turn would increase the Qts, so the mid-bass would prove less pinched. The subwoofer could be driven by an internal power amplifier, which would eliminate the need for large inductors and allow for precise bass level settings. Post 461 showed how an internal subwoofer amplifier could undo a 100Hz high-pass filter placed in front of the main power amplifier. Such a setup could allow for a truly minimalist crossover for the mid-woofers, as a passive crossover might not be much more than a single inductor for the two mid-bass drivers. The high-frequency horn would need a steep high-pass filter, say 3rd-order at 900Hz.

actually, i would like to try a dipole with folded panels.

the idea here is to use three long strips of wood for the front baffle, which would prove sturdier and offer more narrow center section. as shown above, four woofers are used in in a push-pull configuration, wherein the woofer both work in phase, the two drivers that radiate out into the room from their backs are wired out of phase. why bother? woofers give rise to 2nd harmonic distortion due to their preference for one direction of travel. well, placing them in this configuration cancels the distortion to a large degree.

 

 

 

Triadtron Based on the Cathode Follower
The generic cathode follower works well with most higher impedance loads, but bogs down with load impedances that are a small fraction of the triode's plate resistance. For example, if we wish to drive a 300-ohm headphone driver, the 6DJ8's plate resistance is about ten times higher. But the big problem is that even the beefiest triode offers only the smallest fraction of transconductance that a MOSFET or transistor would provide. (The White cathode follower effectively doubles the transconductance and allows push-pull operation.) We can improve the standard cathode follower by using a constant-current source in place of a cathode resistor.

新加坡2分彩计划软件the constant-current source both auto-biases the cathode follower and does not reduce the load impedance the way a cathode resistor must. the problem we often run into is that the cathode voltage is not high enough to allow us to use a solid-state constant-current source, which require a few volts of voltage headroom. the workaround is to use a negative power-supply rail to feed the constant-current source. (the negative rail voltage might be only -6.3vdc, which allow us to heat the heater elements.)

how well does this cathode follower work into a 300-ohm load?

The SPICE Fourier graph reveals a lovely single-ended cascade of harmonics, with the THD coming in a bit less than 1%. For many, this might be the ideal performance, as the single-ended sound will pour forth, but perhaps too ripe for some ears. Another possible arrangement is the Triadtron新加坡2分彩计划软件, which effectively makes the triode function as the constant-current source. Like the cathode follower, the Triadtron is an intrinsically single-ended.

the center circuit is the one we will examine.

the top pnp transistor strives to keep the triode's plate current constant, while the bottom pnp transistor experiences all the current swings needed to drive the external load to its maximum voltage swing. how big can this voltage swing be? roughly it is equal to the triode's idle current against he load impedance. for example, with an idle current flow of 10ma and load impedance of 300 ohms, we could expect to see +/-3vpk of voltage swing—providing that the cathode voltage is sufficiently high enough to encompass the negative voltage swing, say at least 4vdc. (the lower the triode's amplification factor, mu, the higher the cathode voltage will be.) here is a design example that uses an ecc99 that can drive 300-ohm loads.

the 62-ohm plate resistor sets the triode's idle current to about 10ma. the larger this resistor's value is the lower the idle current will be, as the top pnp's base-to-emitter voltage sets the voltage drop across the resistor. the lower the idle current through the triode, the higher the cathode voltage must be, but the lower the output current swings can be.

okay, what can we do to supercharge this cathode-follower-based triadtron circuit? one thing we do is add a diode (or several diodes or zener) to the circuit, which allows us to increase the plate resistor value, which in turn increase the triode's control on the top pnp transistor.

新加坡2分彩计划软件once again, let's use the ecc99 in a design example that contains a bonus 5k resistor.

the 5k resistor draws 31ma, three times that of the triode, which means that we can drive much lower external load impedances, say 75 ohms. what if we want an even lower load impedance, such as 25-ohms. to realize 3vpk voltage swing requires 120ma current swings, which against the high-voltage b+ voltage would result in high dissipation. the workaround is to add a 12vdc power-supply rail, which could be used to power the heater element as well.

the 150ma constant-current source only dissipates 1w, with the mje15033 pnp transistor dissipating slightly less. in contrast, a load resistor to the b+ voltage would dissipate close to 25w of heat. the 330µf non-polarized electrolytic in parallel with the 10µf film coupling capacitor allows bandwidth down to 20hz with 25-ohm headphones. so, how well does this circuit perform? here is the fourier graph from spice simulations with a 32-ohm load and 1vpk at 1khz.

dang! not bad. the thd is 0.02% in spice simulations. note the truly fine attenuation of the third harmonic, which deadens the sound, as peaks are compressed. note, however, that the plain-jane cathode follower exhibited greater attenuation of the 5th and onward harmonics.

新加坡2分彩计划软件okay, how can we further hotrod this circuit? one added feature might be to auto center the output at half the 12vdc power-supply rail voltage. this will require a voltage reference and a negative feedback mechanism to compare the output voltage at the cathode to the reference voltage.

新加坡2分彩计划软件i have added two mje340 npn transistors. the bottom mje340 monitors the cathode voltage at its base through the low-pass rc filter. if the base voltage strays too high, the bottom mje340 increases its current conduction, which will pull down the top mje340's base voltage and in turn lower the ecc99's plate voltage bringing its cathode back inline with the reference voltage. not only does this circuit center the output stage, it vastly improves the psrr, as the top mje340 shields the plate from the b+ voltage ripple. okay, what further hotrodding is possible? in general, when you get the chance, cascode.

新加坡2分彩计划软件the mje350 pnp transistor in cascode with the topmost pnp transistor allows us to use a low-voltage transistor, the 2n4403, to monitor the ac signal that appears across the 120-ohm current-sense resistor. the 33v zener is an added safety feature, as it limits the maximum voltage differential the 2n4403 can see, particularly at startup, when the 10µf electrolytic has yet to fully charge up.

新加坡2分彩计划软件okay, how well does this heavily modified triadtron perform.

although excellent, it's not better than the simpler version. i feel sorry for those readers who don't bother reading, as they are likely to assume that the last circuit shown is the best circuit shown. of course, if the b+ voltage is not regulated or supremely well-filtered, then this last circuit would be the better choice, due to its far better psrr figure. okay, here will be the last variation, which includes some aikido mojo.

新加坡2分彩计划软件the mje15032 is configured as a constant-current source with a difference: psrr enhancement (about a 30db improvement over the stock version). the 10µf capacitor shunting the 1m resistor is about the lowest value i would use, as the greater the capacitance, the lower the aikido-mojo power-supply-noise goes in frequency. the two 1n4148 diodes are there to protect the mje15032 transistor at turn-off. the constant current source could be based on an lm317 positive voltage regulator. in spice simulations, the peak voltage swing ito 32 ohms was 4vpk. (i would have guessed less.) the distortion was only bit over 0.1%.

A nice single-ended cascade.

 

 

Audioquest Nighthawk Carbon Headphones
I have a new pair of headphones that stand apart from most other headphones. I believe that I first heard the at the CanJam room of the RMAF. My first impressions were mixed, as I thought both that they sounded lovely and that they would have hard time competing with high-end competitors. Why? They do not unnaturally sparkle. The highs are reproduced, but they are not blaring in your ears, no sizzling and screeching, not etched in ice.

the prevailing headphone industry assumption must be that audiophiles crave and lust for high-frequencies, so they give it to them good and hard. this assumption, regrettably, might be far closer to the truth than most would care to contemplate. as the average audiophile certainly antiquates the cd, since he may even predate the lp, and because he might be contemporaneous with the 78, the triode, the wax cylinder...his hearing has faded, having suffered the serious spls of rock concerts and the deafening demonstrations of outrageous audio salesmen. alas, age alone attenuates alta acuity.

here is a question for you. how are high-end headphones and handguns alike? answer: most are seldom used.

新加坡2分彩计划软件many, if not most, pistols have never been fired by their owners. something like this holds true with expensive headphones, as i have met plenty of audiophiles who own $$$ headphones but never listen to them. like occasional churchgoers who show up once or twice a year, many audiophiles only listen to their $$$ headphones when impressing their friends, preferring to talk about the sound rather than to listen to it. to be honest, i don't blame them, as the sound from their headphones, while dazzling, cannot bear prolonged listening, much as we cannot stare at burning sparklers for long.

in sharpest contrast, the audioquest nighthawk carbons compel long listening sessions, their sound being so damn quaffable. this does not mean that they are a warm, gooey mess, far from it. in fact, i have been stunned to hear such amazing articulation, especially in the bass, from them—and on music that i have heard many times before. (when i listen to an album for the first time, i zero in on the bass line, as it usually leads to a deeper appreciation of the melodies and direction of the music.) with the nighthawks, the bass notes do not go boom, boom, but plucked, plucked, strummed, strummed, thumped, thumped. the nighthawks are not, however, beats for audiophiles, as the bass is not out of line with the midrange. what might make them sound bass heavy to some is their lack of jacked up brightness, much as we might falsely judge the hips of the movie starlet—without breasts implants—too wide. sometimes, the natural takes getting used to.

in short, the nighthawks were obviously designed by and for music lovers, not hardcore audiophiles. what sort of music best suits them? instantly, 1950s and 60s jazz comes to mind. dave brubeck and miles davis and bill evans cry out to be played on these headphones, preferably late at night, the lights dimmed, the rest of your family either too tired or too distracted by pixels to summon the energy needed bother you, a glass of port or scotch in hand.

     

    

other musical genres well suited to the nighthawks would be the blues, bluegrass, some country, classical (especially if you attend many concerts), most folk (both domestic and international), motown, opera, and 1960s rock. really, any music that expects you to be able to understand words that the singer sings is a good candidate for the nighthawk carbons. and should some album not suit the nighthawks, use a different set of cans, for unlike speakers, headphones cost relatively little and can easily be swapped out.

新加坡2分彩计划软件the nighthawks carbons present a 25-ohm load and play loudly even from my , which was my original motive in buying the headphones, as the phone can play and unfold tidal mqa recordings. in fact, the resulting sound is amazingly good.

when hooked up to discrete headphone amplifier, however, they truly sing, as the bass seems to go an octave lower. they deliver 99db for 1mw (0.224vpk) of input and sport an amazing 1.5w (8.66vpk) maximum output wattage. this is actually an important specification, even though i will never get close to cranking the volume up that much—nor should you. instead, their high power rating means that we can apply equalization without much fear of damaging the headphones. (i would leave the highs alone, preferring to apply a modest boost between 3khz to 6khz.)

the nighthawks carbons are supremely well made and come in a fancy carrying case, with two sets of ear seals. as we would expect from , the cables are first-rate and removable, as each earphone holds its own 3.5mm mono jack. i was happy not to see the ubiquitous gold-plated terminations, but silver instead. most will find the the headphones extremely comfortable. but since my head is so fat (my glasses' frames are made by a company named ), they are a tad tight for me.

audioquest has, sadly, dropped out of the headphone business (well at least that is the rummor). the silver lining here is that these once $700 . if you love tube sound and you love music, pick up a pair before they are all gone.

 

 

 

Book Recommendation: High-Fidelity Techniques
I was searching through my electronics-related PDFs and I found this short book by James R. Langham. What a wonderful read it is, well worth the $1 price charged back in 1950 and its $10 equivalent in today's dollars.


Click on cover to download PDF

the book covers distortion, speakers, amplifiers, amplifier design, power supplies, phonographs, and some last words on high fidelity. here is a sample quote from its introduction:

to me high fidelity means as faithful reproduction as i can manage with my ear and my pocketbook. the state of the art and the state of my purse are limits which prevent me from having nicer stuff than i do. if i were a very rich man, i might hire a symphony orchestra and arturo toscanini to play for me and then i would have very high fidelity indeed. not being rich, i play his records on the best sort of a rig i can make.

fooling around with audio has been a family hobby for a good many years, during that time i have picked up a few little tricks and knacks that make the job easier. some of the information has been dug out of engineering books the hard way, other items have come from bread-boarding the circuits myself. i have built for myself many different outfits and quite a number for others, and, with all the fooling around, the study, the building of this and that, i have learned something about audio.

i am not really an engineer. it is doubtful if there is such a thing as a real audio engineer. the trouble is that it's all subjective. it's not cut and dried. you want to hear what you want to hear, and you wouldn't necessarily be satisfied with what i like to listen to. whether we both happen to like muggsy spannier or palestrina, bebop or fred waring, is coincidental. the chances are we don't like to listen to the same manner of reproduction. your taste doesn't have to coincide with mine any more than with the technicians employed by philco or scott or fisher. nobody has the right to dictate what you should like. if you happen to want a lot of bass-why fine—nothing in the world wrong with your listening to it. if major armstrong builds a gorgeous hunk of set that your neighbor likes, you are perfectly within your rights if you think it stinks. high fidelity audio is a nebulous thing and unpredictable beyond a certain point.

One man spends a whale of a lot of dough on his phonograph and then he spends all his listening time running an audio oscillator through it and listening to somebody jingling keys into a microphone. That's okay too. He's worn out a dozen tone records in the past year, and he rarely plays any music. He doesn't like music.

新加坡2分彩计划软件download the pdf and listen to some frank sinatra and enjoy the read.

 

 

 

Music Recommendation: Secrets Of The Beehive
The great thing about Tidal is that I can quickly bring up albums that I liked long ago, but not enough to buy at the time. One example is Secrets Of The Beehive by David Sylvian. I remember hearing this album on a Virgin CD owned by a friend back in the early 1990s. I found it interesting back then, but enough to overcome my lifelong strong preference for female singers. (In addition, Sylvian's epicene appearance seemed too much an appropriation of the other David, i.e. David Bowie.) Nonetheless, I hoped to find it one day at a garage sale.

well, tidal came to the rescue. hearing it almost 30 years later was interesting, as it sounded at once familiar and new. no doubt, the re-mastering that this 1987 album received in 2003 helped refurbish the sound, which was fresh sounding to begin with. indeed, its minimalist instrumentation helps it sidestep the trap of sounding as dated as its 32 years of age would imply. thank you tidal.

//jrb

 

 

 

 

 

新加坡2分彩计划软件    

User Guides for GlassWare Software
新加坡2分彩计划软件 Just click on any of the above images to download a PDF of the user guides. By the way, all the links for the PCB user guides shown at the right now work.

 

for those of you who still have old computers running windows xp (32-bit) or any other windows 32-bit os, i have setup the download availability of my old old standards: , , and . the downloads are at the glassware-yahoo store and the price is only $9.95 for each program.

新加坡2分彩计划软件so many have asked that i had to do it.

新加坡2分彩计划软件warning: these three programs will not run under vista 64-bit or windows 7 & 8 or any other 64-bit os.

i do plan on remaking all of these programs into 64-bit versions, but it will be a huge ordeal, as programming requires vast chunks of noise-free time, something very rare with children running about. ideally, i would love to come out with versions that run on ipads and android-os tablets.

 

//jrb

 

   

 

 

 

新加坡2分彩计划软件john gives

Special Thanks to the Special 82


To all my patrons, all 76 of them, thank you all again. I want to especially thank

King Heiple

Concordio Anacleto

Kuldeep

Jason Stoddard

Kelvin Tyler

新加坡2分彩计划软件i am truly stunned and appreciative of their support.

新加坡2分彩计划软件in addition i want to thank the following patrons:

John Atwood

Hal Clark

Eduardo Fayad

Mike Galusha

Andreas Hierzenberger

Erik Hoel

Tom Kelly

Thomas Kifowit

Neil Kovacs

Przemek Lach

Ron Lee

Joe Mooney

Seiichiro Nakakura

Paul Reid

Marty Reiss

Paulo Mario dos Santos Dias de Moraes

James Tiemann

all of your support makes a big difference. i would love to arrive at the point where creating my posts was my top priority of the day, not something that i have to steal time from other obligations to do. the more support i get, the higher up these posts move up in deserving attention.

only those who have produced a technical white paper or written an article on electronics know just how much time and effort is required to produce one of my posts, as novel circuits must be created, spice simulations must be run, schematics must be drawn, and thousands of words must be written.

if you have been reading my posts, you know that my lifetime goal is reaching post 1,000. i have 536 more to go.

新加坡2分彩计划软件my second goal is to gather 1,000 patrons. i have 918 patrons to go. help me get there.

 


Only $12.95
to keep track of your
新加坡2分彩计划软件 tube and part collection

TCJ My-Stock DB

TCJ My-Stock DB helps you know just what you have, what it looks like, where it is, what it will be used for, and what it's worth. TCJ My-Stock DB helps you to keep track of your heap of electronic parts. More details.

Version 2 Improvements
  
List all of your parts in one DB.
    Add part Images.
    One-click web searches for part information.
    Vertical and horizontal grids.*
    Create reports as PDFs.*
    Graphs added 2D/3D: pie & bar.*
    More powerful DB search.
    Help system added.
    Editable drop-down lists for location, projects,         brands, styles, vendors and more.

     *user definable

Download for
XP to Win 10

For more information, please visit:

           www.glass-ware.com
 
floridpower.com           Copyright © 1999-2019 GlassWare           All Rights Reserved
一分排列3计划 极速赛车赛车人工计划 北京赛车的8码全天计划表 大发分分彩计划 全天pk非凡计划